Penimaster Pro Review

**Extendernewbie** · 03-23-2016

I was looking EVERYWHERE for a response like this one. I was scared to death when my blisters formed. I accidentally threw out my cd that "I think" have the proper instructions to teach you how to put the device on. I thought that looking at the YouTube videos and following that would suffice. If you could, can you possibly post a video of explaining in detail of how to put it on? I'm not asking for a full penis demonstration, but a showing of how far out you should be inflating the diaphragm(but if you could that would be a greater help). Reason for this is so that I don't have to waste more time on recovery (however long it's gonna take for my blisters to heal) if it were to happen agian.

**Dangler** · 03-23-2016

Start with our 'Buy Now' link, https://www.pegym.com/products/penimaster

You won't need to buy, however you will end up at the US site, where there are plenty of instructions, some videos. You just have to spend time exploring the site to find them.

The goal of inflating the diaphragm outwords, is to eliminate/minimize any air space between the Glans and the latex. Air space encourages 'blistering'. Also, if you try to wear it too long, that can be a factor also.

**wollins** · 03-23-2016

Originally Posted by donjelqer76

I did most of my 900 hours extending with a Penimaster Basic extender, so I was already familiar with the excellent quality of Penimaster's products. I'll be sure to answer any questions if you have any

I also have the Penimaster basic extender from waay back in the day (2003) but thinking of getting back into PE ...

My question is ... can the coupling Socket of this "new" system fit onto the original rods that came with my Penimaster? Would save some coin by not having to buy the "Rod pulling force generator" since I already have the rods!

**Dangler** · 03-23-2016

Probably, given it would be poor economics to have two different parts, when the same part could be used in both models.

**wollins** · 03-24-2016

Originally Posted by donjelqer76
I did most of my 900 hours extending with a penimaster Basic extender, so I was already familiar with the excellent quality of Penimaster's products. I'll be sure to answer any questions if you have any.

Don, just noticed that your original post was in 2012 ... are you still using this? How much did you gain with it?

Thx!

**wollins** · 03-24-2016

Ok so I just read through the entire thread and have realized that Donjelqer has moved on ... but I notice that Dangler has been around this thread since the onset.

So Dangler, are you still using this? How much did you gain with it?

Thx!

**Andrew3000** · 03-24-2016

I find the hose goid. Once I am in and in pisition with the strap or extender, I then open the valve slowly to release the vacuum. I feel the latex form on my head. I don't release so much that my head comes out, jyst enough to reduce the pressure. If I dont use too much lube it stays in place. I occasionally get blisters when I stretch too hard or stau in for 4 hours or so, but they go pretty quickly for me. Its normally a bit of forskin that stays in the vacuum. Releasing the vacuum reduces this happening for me. Good luck.

**Extendernewbie** · 04-13-2016

apparently inflating the diaprham outwards still didnt prevent blisters...im stumped right now....too scared to go longer than 1 30 minutes without checking to c if theres blistering....im feeling like im wasting all my time just taking the thing off then putting it back on and wasting material while im at it

**Dangler** · 04-13-2016

Recently blistered areas will remain prone to being blistered again, and again and again. In my experience, just letting those areas where 'delamination' of skin layers has occurred, heal for a week or so, has helped.

Obviously you cannot wear any device forever, skin just won't co-operate. To some degree, the amount of pulling force applied to the skin comes into play. Air gaps are one of the culprits, but not the only one.

**Marlon LGHanger** · 04-13-2016

Anytime you use a device that employs vacuum as the means of attachment, a certain amount of time is required to develop tissue maturity. This varies from individual to individual, kind of like working on a sun tan! So I suggest you back off on the wear time by at least 50% or more until you find a base line of wear compatibility, then gradually over the next couple months start adding 5 more minutes per week. Dangler is correct about new skin that was once blistered....

I have never used the Peni-master.... but you might consider using wrap for glans protection. This is part of the LG Hanger protocol.