Extender problem, not enough stretch

[melker123]

I just got my X4 deluxe and when I use it I don't get the stretch feeling, obviously the penis stretches but I don't feel it stretch, if it makes any sense. Is it suppose to be like this?

[BBS]

Add some tension until you feel it stretch

[Dangler]

Go by the inscribed lines on each rod. Thats a quantitative measurement. If your just starting out, aim for wearing at the first line slightly covered, leaving the other 2 lines visible.
If you choose to adjust and wear it by the subjective "I need to feel some stretch", the outcome becomes dubious.

[melker123]

Go by the inscribed lines on each rod. Thats a quantitative measurement. If your just starting out, aim for wearing at the first line slightly covered, leaving the other 2 lines visible.
If you choose to adjust and wear it by the subjective "I need to feel some stretch", the outcome becomes dubious.

But when I use it, I push the extender down so it covers the first inscribed line and the when my penis is attached I release it and it goes up again to the first position, that'll say I can then see all the inscribed lines again, the penis is stretched but I doubt that it will become any longer. Am I using it wrong?

[not2big]

But when I use it, I push the extender down so it covers the first inscribed line and the when my penis is attached I release it and it goes up again to the first position, that'll say I can then see all the inscribed lines again, the penis is stretched but I doubt that it will become any longer. Am I using it wrong?

Once you are mounted and all the lines are visible, turn the knob on each bar in a clock wise direction until the first line is justb covered. This will put nice low tension on your penis. After 15 minutes or so, your penis will have relaxed and all three lines will become viable again. So, turn the knobs again until the first line is covered again. Some guys continue to make adjustments to maintain the line covered; however, some advocate leaving it at the first adjustment position.

[Dangler]

At that point one woul begin turning the adjustment screws to lengthen the extender. If you run out of adjustment, then turn the adjustment screws back to minimum, and add a rod section to each side.
Compress X4 extender, mount your self in, release, adjust or fine tune the adjustments.
Usually about 20 to 30 minutes later, the penis will have relaxed, lengthened, causing a reduction in the tension. Adjust as needed.
The X4 forum has a few years of posts, that will give you some ideas, if you are willing to put in the time reading.
good luck !

[melker123]

Once you are mounted and all the lines are visible, turn the knob on each bar in a clock wise direction until the first line is justb covered. This will put nice low tension on your penis. After 15 minutes or so, your penis will have relaxed and all three lines will become viable again. So, turn the knobs again until the first line is covered again. Some guys continue to make adjustments to maintain the line covered; however, some advocate leaving it at the first adjustment position.

But when I turn the knob it only makes it longer no lines are getting covered, and when I turn them to much the bars fall off the base.

[Dangler]

But when I turn the knob it only makes it longer no lines are getting covered, and when I turn them to much the bars fall off the base.

This happens when the extender is too short & needs to be "built" longer. Also after you make it slightly longer, it helps to loosen/warm up your penis, hand stretch, then fasten in. It is just easier, that way.
(from the files)

One basic point, you have to "build" the length of the extender when starting out.
One cannot build up tension by pulling on something that is stretching out as it is being pulled.
Lets say you can stretch your 3" flacid penis to 4".
You will need to construct the rods in your extender so that it is approximately 4". Now there is some variancein the 4", as to where you fasten in at, and a given that you will compress the extender, fasten in to the cradle, then release so the springs take over.
It helps to warm the penis, do some has jelqing, stretching first before fastening in.
So you fasten in, and generally, after 20 to 30 minutes, you penis will relax/stretch out some more, the observed tension lines will show less than you fastened in at. Normal.
What you are tasked to do is decide what tension to adjust to at this point in time. Study this over a few months, and see what best works for you.
There is the tension you mount in at, mounting tension, and half hour later, the tension you are wearing at, wearing tension.

[melker123]

This happens when the extender is too short & needs to be "built" longer. Also after you make it slightly longer, it helps to loosen/warm up your penis, hand stretch, then fasten in. It is just easier, that way.
(from the files)

One basic point, you have to "build" the length of the extender when starting out.
One cannot build up tension by pulling on something that is stretching out as it is being pulled.
Lets say you can stretch your 3" flacid penis to 4".
You will need to construct the rods in your extender so that it is approximately 4". Now there is some variancein the 4", as to where you fasten in at, and a given that you will compress the extender, fasten in to the cradle, then release so the springs take over.
It helps to warm the penis, do some has jelqing, stretching first before fastening in.
So you fasten in, and generally, after 20 to 30 minutes, you penis will relax/stretch out some more, the observed tension lines will show less than you fastened in at. Normal.
What you are tasked to do is decide what tension to adjust to at this point in time. Study this over a few months, and see what best works for you.


There is the tension you mount in at, mounting tension, and half hour later, the tension you are wearing at, wearing tension.

Thank you, I really appreciate all your help, I think I got it now. I apologize if I act stupid, but english is my second language. Take care!