REP Support for Bathpump.com - Q & A

**taichi10** · 01-02-2021

Thank you for your answer.

But what I wanted to know is can I buy only the HydroExtreme 7 pump without the accessories in order to save some money?

**JJballa1996** · 01-02-2021

I'm sitting at 6 x 5.25. I want to get to between 7.5 x 5.75 and 8 x 6. I want to use the bathmate for the girth side of reaching my goal dimensions. I plan to get the hydroextreme.

My issue is, I want to avoid buying two bathmates - one for now and one for when I reach 7 inches in length.

Would a hydroextreme9 work okay at 6 inches at length, for the purpose of girth expansion?

**Walter BP Rep** · 01-05-2021

Originally Posted by taichi10

Thank you for your answer.

But what I wanted to know is can I buy only the HydroExtreme 7 pump without the accessories in order to save some money?

On bathpump.com the kits come free with the models. You can save money with this discount https://www.pegym.com/articles/incre...scount-special

**canadaboi** · 01-05-2021

To anyone who owns a Bathpump: If the black switch on the valve stops working for you (i.e. it is unable to lock, etc.), pop the valve off via putting a flathead screwdriver in between the black cylinder and the translucent, small-cylinder top that encases the black switch. Once you've removed the top, take out the switch. With the switch in-hand, take a knife, razor -- anything sharp and thin -- and cut into the plastic that occupies the place between the switch-part that is visible when fully assembled and spring-esque part -- specifically, the place wherein there resides a right-angle closest to the top of the switch that is horizontal when stationed spring-side down.

I can imagine that this is probably dangerous in that you might accidentally ruin the switch from cutting down too far or too close to the edge, so I'd only really do this if your switch is broken, obviously.

Here's a crude drawing:

https://prnt.sc/wh7a1b

Factoid: Comically, this part looks like a phallus and testicles.

**Walter BP Rep** · 01-08-2021

Originally Posted by canadaboi

To anyone who owns a Bathpump: If the black switch on the valve stops working for you (i.e. it is unable to lock, etc.), pop the valve off via putting a flathead screwdriver in between the black cylinder and the translucent, small-cylinder top that encases the black switch. Once you've removed the top, take out the switch. With the switch in-hand, take a knife, razor -- anything sharp and thin -- and cut into the plastic that occupies the place between the switch-part that is visible when fully assembled and spring-esque part -- specifically, the place wherein there resides a right-angle closest to the top of the switch that is horizontal when stationed spring-side down.

I can imagine that this is probably dangerous in that you might accidentally ruin the switch from cutting down too far or too close to the edge, so I'd only really do this if your switch is broken, obviously.

Here's a rough drawing:

https://prnt.sc/wh7a1b

Factoid: Comically, this part looks like a phallus and testicles.

This post would go good with yours https://www.pegym.com/forums/penis-d...ml#post1323542

**fizzer** · 4 Weeks Ago

Originally Posted by BallsMahoney

Definitely close if not already there. After about 10m in the tube my glans begin to touch the wall where the measuring tape is (perfect upward curve lol), and the sides are very close.

Sounds like x40 is my next move. Do you think the extreme model with hand pump is worth it? Sure looks interesting.

Did you end up getting the X40?

Your base girth is about the same as mine and I've been trying to figure out if the X40 is the right size for me.

I'm 6.682x5.5 for reference.

Edit: or anyone else can comment if the x40 is right for.me with 5.5" BEG

**mafioner** · 4 Weeks Ago

i want to cancel my order and the customer service dont write me back what shoud i do?

**Big Al** · 4 Weeks Ago

Originally Posted by mafioner

i want to cancel my order and the customer service dont write me back what shoud i do?

If you ordered from bathpump.com please contact them at contact@bathpump.com . They should reach back to you in less than 24 hours.

**Walter BP Rep** · 4 Weeks Ago

Originally Posted by mafioner

i want to cancel my order and the customer service dont write me back what shoud i do?

It appears you are in email communication with support now and your order has been cancelled.

**EddyEddy** · 3 Weeks Ago

Hi Harrison, I couldn't see how to search just this thread, so apologies if this has been answered before.

My X40 Extreme started leaking, so I had a look at the two o-rings and saw they were dry and slightly cracked. I revitalised them with some olive oil, and that fixed the problem. But at some point I'm going to need new ones. Are they a standard size or do I need to order them?

Thanks in advance, Ed

p.s. My second goal is within sight, great product!