Penis Extender advice

**zerodown** · 03-04-2015

So... I bought a ProExtender system.

It is a traction device with a loop. I am 5.9inches hard. I have foreskin... So it makes it very hard to use. I haven't been able to get the device on without it slipping off.

I have an idea.. I could easily convert the system into a suction head? Like have a suction head that can be attached to the end of the plate. Is this feasible? Does anyone know how to make a suction cup head for my penis so that I can forgo the loop? I do not want to feel like I just wasted a lot of money.

**pudendal** · 03-04-2015

There are various ways to modify a traditional noose extender to interface with a vacuum attachment system. The autoextender vacextender modification kit is one option that will give you the basics of what you need including a vacuum bell, sleeve, and an adapter with sockets to connect to the rods of your extender. I bought a phallosan system and have made my own DIY adapter to interface it with my old rod-based extender in addition to the belt system. The vacuum attachment is significantly more comfortable than the noose and has drastically improved my daily hours. You might find it would be worth investing in the phallosan to have the belt system as an option to discreetly wear the device in public in addition to the rod extender base for use at home. Another option would be to investigate the various DIY vacuum bells that have been posted on this forum.

**zerodown** · 03-05-2015

I'm not going to lie... I just spent 30 minutes after reading your post to find these Do it yourself vacuum bells to use on my extender system

can someone help me out lol?

**pudendal** · 03-05-2015

Originally Posted by zerodown

I'm not going to lie... I just spent 30 minutes after reading your post to find these Do it yourself vacuum bells to use on my extender system

can someone help me out lol?

Here are a couple threads I had subscribed to for ideas:

https://www.pegym.com/forums/penis-d...-made-lgh.html

https://www.pegym.com/forums/penis-d...lg-design.html

I've also made a couple DIY bells from shampoo bottles but I used valves that I cut out of my smaller phallosan bells:

https://www.pegym.com/forums/penis-d...tml#post993891

https://www.pegym.com/forums/penis-d...tml#post941765

https://www.pegym.com/forums/penis-d...tml#post931938

You could follow my methods for the dome of the bell and use the valve system from some of the other designs. If you're a handy kind of guy who likes to build things, a DIY option might work for you. Otherwise, purchasing something that's already been tested might be the way to go. Good luck!

**KFH** · 03-05-2015

I understand your frustration zerodown, I really do. Pudendal has linked some useful topics on making your own vacuum attachment and also recommended the VacExtender mod.

I'm not sure if you're a dab hand at DIY, but if you're not, the VacExtender isn't a bad route to go down. Just e-mail MB on the website (autoextender.com) prior to ordering to make sure it will fit the specific extender you own, it most likely will, but best to be sure.

You may also want to consider the VLC-tugger (Kit ? VLC Tugger | TLC Tugger Foreskin Restoration). It's difficult to explain, but basically you put a cone with a hook at the top on your exposed glans and then roll your foreskin over the cone. You then place another cone, this time with a hole in the middle, over the foreskin. This creates a vacuum between the foreskin and the glans, you can use the hook on the cone to attach it to your leg, over your shoulder or on a traditional extender. It's a really nifty and comfortable device but it struggles to accommodate those who prefer high level of tension due to slippage and the fact that most men don't have too much foreskin.