How do you REALLY measure the "girth"

[Marvin]

I don't apply any pressure. I just wrap the tape measure around my shaft and let go of one end so that it's touching my shaft all the way around, but is not digging into the skin at all.

There's no right or wrong way though; just be consistent.

Hmm, this is a bit strange. Measuring the length is not a problem for me, but suddenly loosing 0.3 of an inch is a big deal, especially with girth. There must be the correct way the measure it. I also have another question. If I were to penetrate, how much of my girth is actually being used? Seen as it will be compressed... would it be the 5.2" that I measured?

[larrypinball]

If I were to penetrate, how much of my girth is actually being used? Seen as it will be compressed... would it be the 5.2" that I measured?

Marvin, I'd say your correct in that assumption. Well, a bit depending on the vagina though...

From reading the thread it seem most guys are not strangling their dicks, but keeping the measure tape (or whatever method of choice is used) touching the penis all the way around.

Is this such a big deal for you man? I'm sure that when you're in bed those .3 inches are not what counts to your girl! Just keep doing PE and it will grow for sure.

[Marvin]

Aww, this sucks so bad. I mesured it for real for real this time and... It only turned out to be 13-13.5CM (well, at most .5) Which = 5.1-5.3 inches... Man this sucks so bad... When I started I thought I was 5.5" now I measure 5.1"... Thats a big fucking loss. My life couldn't get any worse. fuck fuck... FUCK!

(has anyone else experienced this?)

[larrypinball]

Aww, this sucks so bad. I mesured it for real for real this time and... It only turned out to be 13-13.5CM (well, at most .5) Which = 5.1-5.3 inches... Man this sucks so bad... When I started I thought I was 5.5" now I measure 5.1"... Thats a big fucking loss. My life couldn't get any worse. fuck fuck... FUCK!

Come on Marvin, your life could be way worse! In your position, you are in the absolute best possible place to be... RIGHT HERE on these forums. You will find everything you need here, and a bunch of goodhearted helpful people.

Some time from now you will be glad you did those measurements and you will be proud as hell over the progress you've made - that is if you stick to it, now that you know it's possible!

Loose the attitude and turn it into PE energy; it's not a big fucking loss for you, instead there are some big fucking gains ahead of you!

Good luck! Let me know how it goes.

[Marvin]

Hey Larry, thanks for the advice I think I posted in your thread... Not sure though. How much did you work to get an inch gain in length? Also, did you focus more on length or girth? As your girth didn't shoot up like your length. Just curious.

[larrypinball]

Hey Larry, thanks for the advice I think I posted in your thread... Not sure though. How much did you work to get an inch gain in length? Also, did you focus more on length or girth? As your girth didn't shoot up like your length. Just curious.

Hey again Marvin. Yes, you did post in my progress log. And asked the same questions. The answers are there, check them out...

[Mastermind]

I apply moderate pressure (just enough to cause slight compression) with a seamstress tape. I always measure midshaft because that's the way they do it when compiling statistics on penis size. Measuring at the base is just cheating yourself lol.

[ReetB]

I softly wrap a tailors measure around my dick in three places. The base, the mid-shaft and on the circumcision line behind my head.

That should do the trick

[bodeen]

I use a tailor tape too. Like NP said don't strangle it. I just make sure there isn't any gaps and take my measurement.

[LittleJohn18]

Hey Marvin, maybe the reason behind those different measurement results is you EQ.. just mybe.